Advanced Automotive Technology Model
Units:
- General Shop Safety Practices
- Classroom/Lab Management Procedures
- Tools, Equipment Identification and Utilization
- **Hand tools and hand tool safety (updated) by Curt Erales
- **Measurements and Mathematics (updated) By Michael Drouin
- **Using taps to cut metric and standard threads (updated) by Ramon C. Iniguez
- **Broken Bolt Extraction Methods Part 1 (updated) by Robert Thayer
- **Broken Bolt Extraction Methods Part 2 (updated) by Robert Thayer
- Certification and Licensing
- Vehicle Maintenance Procedures and Documentation
- Fasteners, Gaskets, & Seals
- Engine Systems
- **The 4 strokes of an engine (updated) by Curt Erales
- Ignition System Service (updated) by Curt Erales
- **Bore & Stroke (updated) by John Potter
- **Starting System Fundamentals (updated) by Russell Granger
- **Charging System Fundamentals (updated) by Russell Granger
- **Ingredients to Internal Combustion (updated) by Thomas Dougherty
- **Ingredient 1: Fuel (updated) by Thomas Dougherty
- **Ingredient 2: Compression (updated) by Thomas Dougherty
- **Ingredient 3: Ignition (updated) by Thomas Dougherty
- **Remove and Replace a Valve (updated) by Steve Nagle
- Engine Cooling and Lubrication
- Fuel Systems
- Electrical and Electronic Systems
- **Perform a battery, starter, charging system test using the VAT-40 (updated) by Eli Jaramillo
- **Use of a Multimeter (updated) By Michael Drouin
- **Wiring diagram (updated) By Michael Drouin
- **Fabricate a simple electrical switch (updated) by Ramon C. Iniguez
- **Circuits (updated) By Richie Rizzonelli
- **Ohm's Law (updated) By Richie Rizzonelli
- Engine Performance*
- **Oxygen Sensor Identification **
- Oxygen Sensor Testing 1 **
- Oxygen Sensor Testing 2 (updated) by James Lane
- **Retrieving Diagnostic Trouble Codes (updated) by Dale Critchfield
- Turbocharger System Service (updated) by Dennis Johnson
- Sun Scope Patterns (updated) by John Potter
- **5 Gases (updated) by Michael Fleming
- **Catalytic Converter (updated) by Richard Williams
- **Introduction to the Exhaust Gas Recycling Valve and Systems (updated) by Richard Williams
- **Ignition systems types (updated) by Sergio Marquez
- **Fuel system delivery (updated) by Sergio Marquez
- **Development of Emissions Controls Devices (updated) by Sergio Marquez
- **Typical Computerized Engine Control Operation (updated) by Sergio Marquez
- Chemical, Mechanical, Hydraulic and Physical Principles
- Brake Systems
- Steering, Suspension, Tires, Wheels
- **Shock & Strut Inspection & Service (updated) by Dennis Johnson
- **Tire Mounting Part 1 (updated) by Robert Thayer
- **Tire Mounting Part 2 (updated) by Robert Thayer
- **Lift Safety and Vehicle Lifting (updated) by Robin Coyne
- **Wheel removal and replacement (updated) by Robin Coyne
- **Steering Fundamentals (updated) by Russell Granger
- **Suspension Fundamentals (updated) by Russell Granger
- **Alignment Angles (updated) by Russell Granger
- **Balancing the Tire (updated) by Steve Nagle
- Transmissions and Drivetrains
- **Manual Transmission Power Flow (updated) by Beau Sunahara
- **Gears (updated) by Beau Sunahara
- **Synchronizers (updated) by Beau Sunahara
- **Shift linkage, Interlock, & Detents (updated) by Beau Sunahara
- **Automatic Transmission Service (updated) by Dennis Johnson
- **CV Axle Service (update) by Dennis Johnson
- **Setting Differential Backlash (updated) By Jose Sanchez
- **Introduction to Automatic Transmissions (updated) by Steve Nagle
- Green Concepts
- HVAC (Heating, Ventilation and Air Conditioning)
Tags
Activity Industry Sector
Transportation
Activity Originally Created By:
MaryRose Lovgren
Review
Part of Lesson Plan: Animation Fuel Injectors (updated) by John Potter
Activity Overview / Details
As the students enter the class, they get into their assigned groups. One member from each group will get their group binder from the bookcase. After bringing it to their group, it will be opened and the note pages will be taken out that were given to them the preceding day for this activity. I give out the next day’s activity at the end of each day so the students know what they are going to learn the next day. No Surprises!
Materials / Resource
Fuel Injection 9
[
Download
]
null




