Advanced Automotive Technology Model
Units:
- General Shop Safety Practices
- Classroom/Lab Management Procedures
- Tools, Equipment Identification and Utilization
- **Hand tools and hand tool safety (updated) by Curt Erales
- **Measurements and Mathematics (updated) By Michael Drouin
- **Using taps to cut metric and standard threads (updated) by Ramon C. Iniguez
- **Broken Bolt Extraction Methods Part 1 (updated) by Robert Thayer
- **Broken Bolt Extraction Methods Part 2 (updated) by Robert Thayer
- Certification and Licensing
- Vehicle Maintenance Procedures and Documentation
- Fasteners, Gaskets, & Seals
- Engine Systems
- **The 4 strokes of an engine (updated) by Curt Erales
- Ignition System Service (updated) by Curt Erales
- **Bore & Stroke (updated) by John Potter
- **Starting System Fundamentals (updated) by Russell Granger
- **Charging System Fundamentals (updated) by Russell Granger
- **Ingredients to Internal Combustion (updated) by Thomas Dougherty
- **Ingredient 1: Fuel (updated) by Thomas Dougherty
- **Ingredient 2: Compression (updated) by Thomas Dougherty
- **Ingredient 3: Ignition (updated) by Thomas Dougherty
- **Remove and Replace a Valve (updated) by Steve Nagle
- Engine Cooling and Lubrication
- Fuel Systems
- Electrical and Electronic Systems
- **Perform a battery, starter, charging system test using the VAT-40 (updated) by Eli Jaramillo
- **Use of a Multimeter (updated) By Michael Drouin
- **Wiring diagram (updated) By Michael Drouin
- **Fabricate a simple electrical switch (updated) by Ramon C. Iniguez
- **Circuits (updated) By Richie Rizzonelli
- **Ohm's Law (updated) By Richie Rizzonelli
- Engine Performance*
- **Oxygen Sensor Identification **
- Oxygen Sensor Testing 1 **
- Oxygen Sensor Testing 2 (updated) by James Lane
- **Retrieving Diagnostic Trouble Codes (updated) by Dale Critchfield
- Turbocharger System Service (updated) by Dennis Johnson
- Sun Scope Patterns (updated) by John Potter
- **5 Gases (updated) by Michael Fleming
- **Catalytic Converter (updated) by Richard Williams
- **Introduction to the Exhaust Gas Recycling Valve and Systems (updated) by Richard Williams
- **Ignition systems types (updated) by Sergio Marquez
- **Fuel system delivery (updated) by Sergio Marquez
- **Development of Emissions Controls Devices (updated) by Sergio Marquez
- **Typical Computerized Engine Control Operation (updated) by Sergio Marquez
- Chemical, Mechanical, Hydraulic and Physical Principles
- Brake Systems
- Steering, Suspension, Tires, Wheels
- **Shock & Strut Inspection & Service (updated) by Dennis Johnson
- **Tire Mounting Part 1 (updated) by Robert Thayer
- **Tire Mounting Part 2 (updated) by Robert Thayer
- **Lift Safety and Vehicle Lifting (updated) by Robin Coyne
- **Wheel removal and replacement (updated) by Robin Coyne
- **Steering Fundamentals (updated) by Russell Granger
- **Suspension Fundamentals (updated) by Russell Granger
- **Alignment Angles (updated) by Russell Granger
- **Balancing the Tire (updated) by Steve Nagle
- Transmissions and Drivetrains
- **Manual Transmission Power Flow (updated) by Beau Sunahara
- **Gears (updated) by Beau Sunahara
- **Synchronizers (updated) by Beau Sunahara
- **Shift linkage, Interlock, & Detents (updated) by Beau Sunahara
- **Automatic Transmission Service (updated) by Dennis Johnson
- **CV Axle Service (update) by Dennis Johnson
- **Setting Differential Backlash (updated) By Jose Sanchez
- **Introduction to Automatic Transmissions (updated) by Steve Nagle
- Green Concepts
- HVAC (Heating, Ventilation and Air Conditioning)
Tags
Activity Industry Sector
Transportation
Activity Originally Created By:
MaryRose Lovgren
PUMP IT UP
Part of Lesson Plan: **Inspection and Pressure Testing of Cooling System (updated) By Jose Sanchez
Activity Overview / Details
Students will gather in groups of three and I will demonstrate what we are looking for in a visual inspection. I will then perform a cooling system pressure test. I will cover all safety aspects and make sure all students are wearing PPE (personal protective equipment).
