Automotive General Services Technician Model
Units:
- Shop Safety Practices
- Classroom/Lab Management Procedures
- Tools, Equipment Identification and Utilization
- **Broken Bolt Extraction Methods Part 2 (updated) by Robert Thayer
- **Hand tools and hand tool safety (updated) by Curt Erales
- **Measurements and Mathematics (updated) By Michael Drouin
- **Using taps to cut metric and standard threads (updated) by Ramon C. Iniguez
- **Broken Bolt Extraction Methods Part 1 (updated) by Robert Thayer
- Certification and Licensing
- Vehicle Maintenance Procedures and Documentation
- Fasteners, Gaskets, & Seals
- Engine Systems
- **The 4 strokes of an engine (updated) by Curt Erales
- Ignition System Service (updated) by Curt Erales
- **Bore & Stroke (updated) by John Potter
- **Catalytic Converter (updated) by Richard Williams
- **Starting System Fundamentals (updated) by Russell Granger
- **Charging System Fundamentals (updated) by Russell Granger
- **Ingredients to Internal Combustion (updated) by Thomas Dougherty
- **Ingredient 1: Fuel (updated) by Thomas Dougherty
- **Ingredient 2: Compression (updated) by Thomas Dougherty
- **Ingredient 3: Ignition (updated) by Thomas Dougherty
- **Remove and Replace a Valve (updated) by Steve Nagle
- Engine Cooling and Lubrication
- Fuel System
- Electrical and Electronic Systems
- **Perform a battery, starter, charging system test using the VAT-40 (updated) by Eli Jaramillo
- **Use of a Multimeter (updated) By Michael Drouin
- **Wiring diagram (updated) By Michael Drouin
- **Fabricate a simple electrical switch (updated) by Ramon C. Iniguez
- **Circuits (updated) By Richie Rizzonelli
- **Ohm's Law (updated) By Richie Rizzonelli
- Engine Performance
- **Oxygen Sensor Identification (updated) by James Lane
- **Development of Emissions Controls Devices (updated) by Sergio Marquez
- **Typical Computerized Engine Control Operation (updated) by Sergio Marquez
- Live Engine
- ECM or PCM
- The Major Primary Input Sensors
- The Major Outputs and Actuators
- Input and Output Sensors Identification
- Clean up
- **5 Gases (updated) by Michael Fleming
- **5 Gas Analysis (updated) by Richard Williams
- **Retrieving Diagnostic Trouble Codes (updated) by Dale Critchfield
- Turbocharger System Service (updated) by Dennis Johnson
- Oxygen Sensor Testing 1 **
- Oxygen Sensor Testing 2 **
- Sun Scope Patterns (updated) by John Potter
- **Introduction to the Exhaust Gas Recycling Valve and Systems (updated) by Richard Williams
- **Ignition systems types (updated) by Sergio Marquez
- **Fuel system delivery (updated) by Sergio Marquez
- **Catalytic Converter (updated) by Richard Williams
- Chemical, Mechanical, Hydraulic and Physical Principles
- Brake Systems
- Steering, Suspension, Tires, Wheels
- **Shock & Strut Inspection & Service (updated) by Dennis Johnson
- **Tire Mounting Part 1 (updated) by Robert Thayer
- **Tire Mounting Part 2 (updated) by Robert Thayer
- **Lift Safety and Vehicle Lifting (updated) by Robin Coyne
- **Wheel removal and replacement (updated) by Robin Coyne
- **Steering Fundamentals (updated) by Russell Granger
- **Suspension Fundamentals (updated) by Russell Granger
- **Alignment Angles (updated) by Russell Granger
- **Balancing the Tire (updated) by Steve Nagle
- Transmissions and Drivetrains
- **Gears (updated) by Beau Sunahara
- **Synchronizers (updated) by Beau Sunahara
- **Shift linkage, Interlock, & Detents (updated) by Beau Sunahara
- **Manual Transmission Power Flow (updated) by Beau Sunahara
- **Setting Differential Backlash (updated) By Jose Sanchez
- **Automatic Transmission Service (updated) by Dennis Johnson
- **CV Axle Service (update) by Dennis Johnson
- **Introduction to Automatic Transmissions (updated) by Steve Nagle
- Green Concepts
- HVAC (Heating, Ventilation and Air Conditioning)
Tags
Activity Industry Sector
Transportation
Activity Originally Created By:
MaryRose Lovgren
Input and Output Sensors Identification
Part of Lesson Plan: **Typical Computerized Engine Control Operation (updated) by Sergio Marquez
Activity Overview / Details
Break the class into groups of two, and give them the list of parts covered in the lectures. Have them go out to different vehicles and identify each part and location.
Make your list for the vehicles you have in the shop.
